Search found 256 matches

by arhi
Wed Nov 02, 2016 1:40 am
Forum: General Discussion
Topic: Help for my thesis
Replies: 2
Views: 3405

Re: Help for my thesis

Sorry, the file you have requested does not exist.

Make sure that you have the correct URL and the file existed.
by arhi
Thu Oct 20, 2016 2:18 pm
Forum: UP Plus
Topic: Smooties board for up plus 2 help...
Replies: 5
Views: 4470

Re: Smooties board for up plus 2 help...

btw there's a separate homing thing with smoothieware, you can set this value (gamma_max) in config and it's the value that will be loaded as Z position after you home (because gamma_homing_direction is set to home_to_max so on homing of Z the gamma_max is loaded, X and Y are loading min value when ...
by arhi
Thu Oct 20, 2016 2:03 pm
Forum: UP Plus
Topic: Smooties board for up plus 2 help...
Replies: 5
Views: 4470

Re: Smooties board for up plus 2 help...

fei8820 wrote:Thanks !! i going to looking where i can setup the beg height ... :mrgreen:
this line:
gamma_max 136.5

that's my value, change for value that suits you :D
when you change config restart printer
by arhi
Wed Oct 19, 2016 11:39 pm
Forum: UP BOX & UP BOX+
Topic: Lost confidence with the UP Box
Replies: 16
Views: 18443

Re: Lost confidence with the UP Box

The UP BOX Studio software does not provide any control of fan speed by layer. dunno how it is on other printers like up box, but up!plus2 has only one fan and that one is linked to "motor enable" pin on the cpu so it can only be on and off and it has to be on while printer is running (when you ena...
by arhi
Wed Oct 19, 2016 4:30 pm
Forum: UP Plus
Topic: Smooties board for up plus 2 help...
Replies: 5
Views: 4470

Re: Smooties board for up plus 2 help...

note this config is for up! Plus 2, it's not same for other TT printers
by arhi
Wed Oct 19, 2016 4:28 pm
Forum: UP Plus
Topic: Smooties board for up plus 2 help...
Replies: 5
Views: 4470

Re: Smooties board for up plus 2 help...

you need
1. version of firmware that support PT100 (not yet in the smoothieware main tree)
2. config file

here's both attached, unzip and copy both files on the sd card and restart the smoothieware (power off/on the up, make sure you "eject" the disk on windoes) and try then :D
by arhi
Wed Oct 19, 2016 3:53 pm
Forum: Look! My Mod
Topic: Custom MCU-module for UP! Mini...
Replies: 170
Views: 152551

Re: Custom MCU-module for UP! Mini...

Yea..I did thought of that but the routing is getting a bit cramped so I gave up.. :cry: :( well if the pins are free and used for soemthing else (the eth ones) I'll try to bodge something directly on top of this board .. ain't going to be easy from what I see :( if you only at least left a small h...
by arhi
Wed Oct 19, 2016 11:42 am
Forum: Look! My Mod
Topic: Custom MCU-module for UP! Mini...
Replies: 170
Views: 152551

Re: Custom MCU-module for UP! Mini...

Octoprint works quite well for me :) hm .. if you remembered to add eth phy on board and pinheader for the eth jack you would not need another computer attached to the up to serve as web server :( ... i'm these days looking at how to make a small board with phy+eth jack to bodge on top of your repl...
by arhi
Fri Oct 14, 2016 11:38 pm
Forum: Look! My Mod
Topic: Custom MCU-module for UP! Mini...
Replies: 170
Views: 152551

Re: Custom MCU-module for UP! Mini...

if you have a second printer to tinker with maybe you can leave up with existing cpu and give them a chance to fix the studio .. or not .. dunno .. I was super positive when the studio got temperature fix but I have some builtin frustration that's probably misplaced and not really TT's fault and I r...
by arhi
Thu Oct 13, 2016 1:46 pm
Forum: Look! My Mod
Topic: Custom MCU-module for UP! Mini...
Replies: 170
Views: 152551

Re: Custom MCU-module for UP! Mini...

Any updates on this? Did you manage to get it better calibrated? I am tempted to also make the switch... :mrgreen: it really depends how much do you want to tinker, I don't mind and it works perfectly for me... you can see here, perfectly calibrated: https://www.up3d.com/community/viewtopic.php?p=4...
by arhi
Wed Oct 12, 2016 11:40 am
Forum: UP Software
Topic: UP Studio vs Simplify3D
Replies: 22
Views: 24583

Re: UP Studio vs Simplify3D

Hi Jason :D wrt that picture - I NEVER managed to get that from my UP!PLus2, never! not with original white ABS that came with printer, not with other white ABS spool from TT nor with colido ABS nor ensun ABS nor any other one I tried... to print this and have them match without sanding it was just ...
by arhi
Wed Oct 12, 2016 5:20 am
Forum: UP Software
Topic: UP Studio vs Simplify3D
Replies: 22
Views: 24583

Re: UP Studio vs Simplify3D

this is not just simplify3d as I replaced the cpu too and am now running smoothieware but for e.g. I was never able to calibrate UP! before to print matching parts... every time I'd have to design parts with huge slack in order for parts to be able to fit into each other snuggly .. and that was alwa...
by arhi
Sun Oct 02, 2016 4:03 pm
Forum: UP Plus
Topic: Unable to finish initialise ...
Replies: 5
Views: 4098

Re: Unable to finish initialise ...

tinyfab don't have many of those boards so if you r interested i suggest getting one asap :) ... I doubt I'm returning original board back in to my up plus 2 :)
by arhi
Sun Oct 02, 2016 1:21 am
Forum: UP Plus
Topic: Unable to finish initialise ...
Replies: 5
Views: 4098

Re: Unable to finish initialise ...

works perfect with UP! plus :D

viewtopic.php?f=28&t=22192&start=80#p47273
by arhi
Fri Sep 30, 2016 8:42 pm
Forum: Look! My Mod
Topic: Custom MCU-module for UP! Mini...
Replies: 170
Views: 152551

Re: Custom MCU-module for UP! Mini...

output .. damn good .. for start, no calibration yet (need to increase extruder flow from what i see attm) but for uncalibrated print .. hahaha it's as good as up studio :D .. better handle of the bridges for sure (this is only 10% infill)
s3d-up.jpg
1st print - s3d->smoothie->up
s3d-up.jpg (989.27 KiB) Viewed 16525 times
by arhi
Fri Sep 30, 2016 8:35 pm
Forum: Look! My Mod
Topic: Custom MCU-module for UP! Mini...
Replies: 170
Views: 152551

Re: Custom MCU-module for UP! Mini...

hahah if wojks :D some calibration needed still to get ideal results but so far I'm super happy with how it works .. s3d.JPG Also attached is ZIP containing smoothieware firmware with PT100 enabled (I hope my pull request for this PT100 addon will go into main tree but for now here's the working fir...
by arhi
Fri Sep 30, 2016 10:22 am
Forum: UP Plus
Topic: how to export .UP3 to STL
Replies: 6
Views: 7357

Re: how to export .UP3 to STL

you have these on thingiverse 1. the wind barrier (what heats the extruder and has no door for PLA): http://www.thingiverse.com/thing:253687 2. what pushes on top of that fan to gather fresh air: http://www.thingiverse.com/thing:253694 3. the part that goes over motor and cools it: http://www.thingi...
by arhi
Fri Sep 30, 2016 10:13 am
Forum: Look! My Mod
Topic: Custom MCU-module for UP! Mini...
Replies: 170
Views: 152551

Re: Custom MCU-module for UP! Mini...

dunno if older pcb's have that DOUPTZ header or not, but it's definetely usable now
by arhi
Fri Sep 30, 2016 4:00 am
Forum: Look! My Mod
Topic: Custom MCU-module for UP! Mini...
Replies: 170
Views: 152551

Re: Custom MCU-module for UP! Mini...

DOUPTZ connector on board (the 3mm banana connector exposed back of the machine used for nozzle height detection and bed leveling) schematic reverse engineered .. if anyone needs it for anything :D pin1 of the DOUPTZ 4 pin header on board -> sleeve of the 3mm banana connector is GND pin2/3/4 (ring1,...
by arhi
Thu Sep 29, 2016 11:06 pm
Forum: UP Plus
Topic: how to export .UP3 to STL
Replies: 6
Views: 7357

Re: how to export .UP3 to STL

what part you need, maybe we can find a stl of that part :)