Search found 16 matches

by Rene1981
Sun Jun 01, 2014 12:45 pm
Forum: General Discussion
Topic: Printing with rubber on Up! plus 2
Replies: 1
Views: 3508

Printing with rubber on Up! plus 2

Hello, does anyone tried printing with Rubber on the Up! plus 2? If yes, can you please tell me how it works and what your experiences are with this filament? Also, what kind of config do I have to use for this filament? And where did you buy your rubber filament? Thanks a lot! With kind regards, René
by Rene1981
Sat May 31, 2014 9:13 pm
Forum: UP Plus
Topic: Print stopped at 75%
Replies: 12
Views: 10392

Re: Print stopped at 75%

Hello Jay,

did you try another object to print? and did you have the same problem with it?
by Rene1981
Fri May 30, 2014 3:05 pm
Forum: Netherlands
Topic: PLA printen met de Up! plus 2
Replies: 1
Views: 4196

PLA printen met de Up! plus 2

Hoi,

heeft iemand ervaring met het printen met PLA voor de Up1 plus 2?
Ik heb tot nog toe altijd met ABS geprint en ik ben benieuwd hoe het nu met PLA werkt.

Bedankt!

Gr. René
by Rene1981
Fri May 30, 2014 3:04 pm
Forum: Netherlands
Topic: Rubber printen met de Up! plus 2
Replies: 1
Views: 4327

Rubber printen met de Up! plus 2

Hoi,

heeft iemand ervaring met rubber printen met de Up! plus 2?
Dat schijnt te kunnen namelijk.

Graag hoor ik jullie ervaringen ermee en hoe ik dan eventueel de printer moet instellen.

Gr. René
by Rene1981
Thu May 22, 2014 4:31 am
Forum: UP Plus
Topic: Problem with removeming surface filament
Replies: 6
Views: 5822

Re: Problem with removeming surface filament

Hey Caesar,

I didn't change the software version.
by Rene1981
Wed May 21, 2014 3:57 pm
Forum: UP Plus
Topic: Problem with removeming surface filament
Replies: 6
Views: 5822

Re: Problem with removeming surface filament

Hello, thanks for your reactions so far. Unfortunatly it didn't help. I tried printing with open and closed wind barrier, with other filament (new role and older one), with less or more surface layers, but it still won't work like before. I also calibrated the printplatform again, but that didn't he...
by Rene1981
Wed May 21, 2014 4:22 am
Forum: UP Plus
Topic: Problem with removeming surface filament
Replies: 6
Views: 5822

Re: Problem with removeming surface filament

If you are using non genuine filament it is because it is too hot - get a temp mod. If it's genuine then open the wind barrier after the initial couple of base layers are laid but before your real print layer starts. Hello Roller, I use genuine filament, and the Up! plus is an open printer, so I ca...
by Rene1981
Tue May 20, 2014 11:18 am
Forum: UP Plus
Topic: Problem with removeming surface filament
Replies: 6
Views: 5822

Problem with removeming surface filament

Hello, since a few months, I've got a problem with removing the supporting filament from the object I want: - You have the filament on the printerbed , form printerbed to printerbed (thats not a problem) - And you have the filament at the object, from printerbed to the object (and thats a problem) I...
by Rene1981
Sat Dec 28, 2013 10:54 am
Forum: UP Plus
Topic: Noise
Replies: 6
Views: 5239

Re: Noise

Its still peeping a bit, but its not a problem anymore for me.

Thanks for your help!

Gr. René
by Rene1981
Sat Dec 28, 2013 10:51 am
Forum: UP Plus
Topic: Still problems with 1 corner of my printbed
Replies: 5
Views: 4667

Re: Still problems with 1 corner of my printbed

Sorry for my late respons.

It worked with your answers.

Thanks for your help!

Gr. René
by Rene1981
Sat Dec 28, 2013 10:49 am
Forum: UP Plus
Topic: Print is getting lose from printbed
Replies: 3
Views: 3556

Re: Print is getting lose from printbed

Sorry for my late repsons.
With your help it worked.

Thanks!

Gr. René
by Rene1981
Mon Nov 18, 2013 8:05 am
Forum: UP Plus
Topic: Still problems with 1 corner of my printbed
Replies: 5
Views: 4667

Re: Still problems with 1 corner of my printbed

Sounds like your print BED is NOT level, you need to check that it is level in the maintenance screen, by moving the head around and checking the height is the same, it will be lower where it lifts up, don't worry about printing the calibration example just yet, level your print bed first, and you ...
by Rene1981
Sat Nov 16, 2013 9:42 pm
Forum: UP Plus
Topic: Still problems with 1 corner of my printbed
Replies: 5
Views: 4667

Still problems with 1 corner of my printbed

Hello, I get still problems with 1 corner of my printbed. When i have to print in that corner, the filament is losing in that corner. (It comes up.) In the other area, i don't have that problem, then my filament is fitting to my printbed. Because of that problem, I can't print my callibration exampl...
by Rene1981
Fri Nov 15, 2013 5:33 pm
Forum: UP Plus
Topic: Noise
Replies: 6
Views: 5239

Noise

Hello,

my up plus 2 printer, makes a litlle peping noise wenn printing, and you can hear the printbed and the nozzle moving.
Can it be that my nozzle is too close to my printbed?

Gr. René
by Rene1981
Fri Nov 15, 2013 5:32 pm
Forum: UP Plus
Topic: Wattage?
Replies: 1
Views: 2506

Wattage?

Hey,

can someone please tell me how much watt the up plus 2 printer use for 1 hour printing?

Thanks a lot!

Gr. René
by Rene1981
Sat Nov 09, 2013 7:52 pm
Forum: UP Plus
Topic: Print is getting lose from printbed
Replies: 3
Views: 3556

Print is getting lose from printbed

Hello,

wenn I try to print a some bigger print, the print is getting lose from the printbed. And then the print is destroyed :( That costs me too much filament and time.
I use ABS, with 0,15 mm layers. Its a heated bed too.

Can someone help me what I can do?

Thanks a lot!


Gr. René