Search found 74 matches

by Matchpoint
Wed May 25, 2016 1:40 pm
Forum: General Discussion
Topic: Up Studio
Replies: 74
Views: 74761

Re: Up Studio

ya it went from bad to worse... the up box is a great printer, I would total buy a personal one if it was open sourced or at least had features that were nice to use on the software side of it. this software is horrible....was thinking about an up mini2, but if this is whats its going too I am going...
by Matchpoint
Tue Apr 12, 2016 9:52 pm
Forum: UP Software
Topic: Up Studio 0.10 is now out lets put bug reports here
Replies: 24
Views: 18740

Re: Up Studio 0.10 is now out lets put bug reports here

I have a very good computer and it is still laggy.
by Matchpoint
Fri Apr 08, 2016 9:17 pm
Forum: UP Software
Topic: What the UP Studio should look like
Replies: 13
Views: 11542

Re: What the UP Studio should look like

I have never used Simplify3d, but now I can see that all my issues that have been arising with print strengths and infill, etc are due to the software constraints! These guys know what's up :lol: How can we solve this? once you use s3d you will be blown away if all you have been using is the UP sof...
by Matchpoint
Mon Mar 28, 2016 12:59 am
Forum: UP BOX & UP BOX+
Topic: Up Box Lubricants : available in rational quantities?
Replies: 3
Views: 4997

Re: Up Box Lubricants : available in rational quantities?

ricks01 wrote:Well, for what it's worth, I have been using Mobil 1 Synthetic Grease and 3-in-1 multipurpose oil on my printers...
Same here the pink stuff
by Matchpoint
Sat Mar 26, 2016 2:43 pm
Forum: General Discussion
Topic: UP mini 2
Replies: 7
Views: 6520

Re: UP mini 2

ricks01 wrote:Link would be nice...
http://www.up3dusacart.com/ttc01/
by Matchpoint
Sat Mar 26, 2016 2:41 pm
Forum: Look! My Mod
Topic: WORKING: SOFTWARE TEMP MOD - ADJUSTABLE LAYER HEIGHTS !
Replies: 142
Views: 145049

Re: WORKING: SOFTWARE TEMP MOD - ADJUSTABLE LAYER HEIGHTS !

For some reason up has the default set at .3 because it works better. Use .3 it works better even though you actually have a .4 nozzle Hello, one small question. The default "Nozzle" diameter is 0.4 mm but. Do I have to "Nozzel Diameter" as 0.400000 "Enter? 0.300000 is green and is standard, but the...
by Matchpoint
Fri Mar 25, 2016 4:39 pm
Forum: General Discussion
Topic: UP mini 2
Replies: 7
Views: 6520

UP mini 2

Pre-order is up. shipping in may 2016.

$599
by Matchpoint
Tue Mar 22, 2016 3:13 pm
Forum: UP BOX & UP BOX+
Topic: My UP BOX problems
Replies: 45
Views: 41007

Re: My UP BOX problems

car3less wrote:Yes. I contacted everyone.
I received a new printer. And prints are very good. I had no failures in more than 10 prints.

I added pictures on the previous page of the topic.
same thing happened to me 2nd printer works perfect
by Matchpoint
Mon Mar 21, 2016 2:12 pm
Forum: Official Announcement
Topic: Take survey and win $100 up3d.com cash coupon
Replies: 22
Views: 19918

Re: Take survey and win $100 up3d.com cash coupon

Tiertime-Jason wrote:We have problem sending emails to some prize winners, the mails bounced.
We are still trying....... ;)
Any update on the software update Jason :-D
by Matchpoint
Fri Mar 18, 2016 4:59 pm
Forum: UP mini
Topic: Turn off the beeping noise
Replies: 5
Views: 7024

Re: Turn off the beeping noise

ricks01 wrote:
Matchpoint wrote:there is a cover you can print on thingiverse for this as well. I can't seem to find it but I know its on there, it shows a picture of an orange cover.
It won't turn off the beeping but it does make it a little quieter...

http://www.thingiverse.com/thing:31957
I knew I wasnt crazy haha thanks
by Matchpoint
Fri Mar 18, 2016 3:01 pm
Forum: UP BOX & UP BOX+
Topic: Job failing after first 3mm
Replies: 11
Views: 9095

Re: Job failing after first 3mm

can you take a picture of the first layer you put down, and are you using a raft?
You can sometimes get to low of a layer height and can clog the nozzle, try raising your nozzle height.
by Matchpoint
Fri Mar 18, 2016 1:25 pm
Forum: UP BOX & UP BOX+
Topic: Job failing after first 3mm
Replies: 11
Views: 9095

Re: Job failing after first 3mm

What material is it?
Do you have the new cover where the filament feeds through the top or does it feed into the side of the extruder?
What is it exactly doing? Does it clunk?
by Matchpoint
Fri Mar 18, 2016 1:23 pm
Forum: UP mini
Topic: Turn off the beeping noise
Replies: 5
Views: 7024

Re: Turn off the beeping noise

there is a cover you can print on thingiverse for this as well. I can't seem to find it but I know its on there, it shows a picture of an orange cover.
by Matchpoint
Thu Mar 17, 2016 1:34 am
Forum: Look! My Mod
Topic: My final PLA solution…
Replies: 6
Views: 7482

Re: My final PLA solution…

Maybe I have good luck but I print in pla all the time. Heat sinks and fans blowing on stepper motor and hot end heat sink worked great.
by Matchpoint
Tue Mar 15, 2016 1:57 pm
Forum: Official Announcement
Topic: Take survey and win $100 up3d.com cash coupon
Replies: 22
Views: 19918

Re: Take survey and win $100 up3d.com cash coupon

well that makes me feel special then. Though I am looking more forward to the new software and hardware updates over anything else. Thank you Tiertime!
by Matchpoint
Tue Mar 15, 2016 1:48 pm
Forum: UP mini
Topic: [solved] Can I use 2.85 mm PLA instead of 1.75 mm
Replies: 3
Views: 4190

Re: Can I use 2.85 mm PLA instead of 1.75 mm

Ya it wont fit anywhere in the extruder at all. need to use 1.75mm
by Matchpoint
Mon Mar 14, 2016 2:48 pm
Forum: UP Plus
Topic: Rapidly Blinking Light
Replies: 4
Views: 4065

Re: Rapidly Blinking Light

This happens as well for me from time to time. I think it is an error in the firmware after you do the right combination of things. Good practice for me, is to turn off the machine. Unplug the machine for like 15 seconds so the capacitors drain. Then restart and reinitialize and it should work ok.
by Matchpoint
Mon Mar 14, 2016 2:44 pm
Forum: Official Announcement
Topic: Take survey and win $100 up3d.com cash coupon
Replies: 22
Views: 19918

Re: Take survey and win $100 up3d.com cash coupon

I think everyone who took the survey got a coupon which is awesome!~ What country are you located in? I am looking forward to the software more :-D I am in Russia, the question is just what I can order with this coupon, as I don't need another printer and shipping of filament is cost prohibitive. O...
by Matchpoint
Mon Mar 14, 2016 1:28 pm
Forum: Official Announcement
Topic: Take survey and win $100 up3d.com cash coupon
Replies: 22
Views: 19918

Re: Take survey and win $100 up3d.com cash coupon

So I got email that I won, but can I use this coupon to purchase spare parts for Up Box? I am interested in UP Flex Print Board and maybe HEPA filter. Right now only printers and filaments are available. I think everyone who took the survey got a coupon which is awesome!~ What country are you locat...
by Matchpoint
Sun Mar 13, 2016 11:27 pm
Forum: UP Software
Topic: UP Studio
Replies: 11
Views: 10343

Re: UP Studio

Liova wrote:Are you telling that Up BOX has Wifi hardware and it will be a software only upgrade?
No it will be a hardware upgrade